[LONGER]LSP 주입/흡입식정밀주사기펌프

LSP 주입/흡입식 정밀 주사기펌프 [LSP Series Syringe Pumps] LSP02-1B 주입/흡입식 2-채널 주사기펌프 LSP10-1B 주입/흡입식 10-채널 주사기펌프 LSP01B-1BH 주입/흡입식 1-채널 고압주사기펌프  LSP01C-1C 푸쉬/풀식 2-채널 주사기펌프

개 요 LSP 주사기펌프는 설치와 작동이 간편하고 높은 정밀도와 신뢰성을 제공하는 실험실용 표준형 주사기펌프이다. 주입전용 제품으로 공급되며, 10 µL에서 60 mL 주사기를 장착할 수 있다. 대형 LCD 화면에서 회전스위치와 멤브레인키패드를 이용하여 파라메터의 설정을 간편하게 할 수 있다

특 징 Syringe Selection : The syringe can be selected in the manufacturer table which includes manufacturer,    material and size or input the inner diameter of the syringe barrel directly Easy to operate: Combining big screen LCD display with rotary coded switch and membrane keypad makes    the operation simple and prompt. Working Mode: Infusion, withdrawal, infusion/withdrawal, withdrawal/infusion, continuous Memory Function : 1. The parameters are saved in EEPROM.    The parameters don't need to be reset when power returns after an interruption 2. In flow rate mode, the pump remains running or stop according to the setting parameters when power returns     after an interruption Protection Function : The pump will stall and give an alarm when the drive structure of the pump is blocked Communication Function : Realize computer control through RS485 communication interface Calibration Function : Acquire accurate volume through calibration: Input/output control Syringe Protection : Adjust syringe rest to prevent syringe from damaging

규 격  + 확대한 그림보기-> LSP02-1B LSP10-1B LSP01-1BH LSP01-1C Working Mode Infusion/Withdrawal Push/Full Channel 2 10 1 2 Syringe 10 uL ~ 60 mL 10 uL ~ 10 mL 10 uL ~ 100 mL 10 uL ~ 10 mL Stroke 140 mm Pusher Advance 0.156 um/step Linear Speed 5 um/min~130 mm/min 5um/min~65mm/min Linear Resolution 5 um/min Linear Accuracy ≤±0.5% when ≥30% of pump stroke Linear Force ≥18 kg (40 lbs) ≥45 kg (99 lbs) ≥9 kg (20 lbs) Syringe Selection Built-in syringe branched, size and inner diameters Syringe Defined Can store four user-defined syringe inner diamerters Flowrate Calibration Improve flowrate accuracy Running Parameter Infusion/withdrawal volume, infusion/withdrawal time, pause time, etc Display Setting Display volume, flowrate or linear speed Power-off Memory Storing the running parameters automatically State Output OC gate signal to indicate start/stop and direction Control Input Falling edge or TTL signal to control Start/Stop Communication RS-485 Diemensin 280Lx210Wx140mmH 280Lx330Wx140mmH 280Lx250Wx140mmH 280Lx220Wx140mmH Weight 4.3 kg 5.3 kg 6.3 kg 3.6 kg Power AC 90-260V/20W AC 90-260V/25W AC 90-260V/15W Syringe  Diameter (mm) LSP02-1B (uL/min~mL/min)  LSP10-1B (uL/min~mL/min)  LSP01-1C (uL/min~mL/min) 10 uL 0.50 0.001-0.0255 0.001-0.0255 0.001-0.0128 25 uL 0.80 0.0025-0.0653 0.0025-0.0653 0.0025-0.0327 50 uL 1.10 0.0048-0.1235 0.0048-0.1235 0.0048-0.0618 100 uL 1.60 0.0101-0.2614 0.0101-0.2614 0.0101-0.1307 250 uL 2.30 0.0208-0.5401 0.0208-0.5401 0.0208-0.2701 500 uL 3.25 0.0415-1.0784 0.0415-1.0784 0.0415-0.5392 1.0 mL 4.72 0.0875-2.2747 0.0875-2.2747 0.0875-1.1373 2.0 mL 9.00 0.3181-8.2702 0.3181-8.2702 0.3181-4.1351 5.0 mL 13.10 0.6739-17.522 0.6739-17.522 0.6739-8.7608 10 mL 16.60 1.0821-28.135 1.0821-28.135 1.0821-14.068 20 mL 19.00 1.4176-36.859 - - 30 mL 23.00 2.0774-54.012 - - 60 mL 29.14 3.3346-86.699 - - Syringe  Diameter (mm) LSP01-1C (uL/min~mL/min) Outlet Pressure (Mpa) 2.5 mL 4.79 0.0901-2.3426 19.48 8.0 mL 9.53 0.3567-9.2730 5.05 20 mL 19.13 1.4371-37.3648 1.25 50 mL 28.6 3.2121-83.5152 0.56 100 mL 34.9 4.7831-124.361 0.37

주문정보 Model Product code Channel Pusher Advance Linear Force LSP02-1B 050344A 2 0.156 um/step ≥18 kg (40 lbs) LSP10-1B 050346A 10 0.156 um/step ≥18 kg (40 lbs) LSP01-1BH 050343A 1 0.156 um/step ≥45 kg (99 lbs) LSP01-1C 050342A 1 0.156 um/step ≥9 kg (20 lbs) LSP01-1BH High Pressure Syringe Pump SS syringe Tube length Stroke length Outer diameter Inner diameter Total length 8 mL 170 mm 110.5 mm 14 mm 9.53 mm 203 mm 20 mL 120 mm 68.4 mm 22 mm 19.13 mm 144 mm 50 mL 140 mm 76.8 mm 32 mm 28.6 mm 165 mm 100 mL 170 mm 107.0 mm 38 mm 34.9 mm 210 mm LSP01-1C Push/Full Syringe Pump

기술자료 LSP02(10)-1B Syringe Pump External control port (Release Time：2017-01-06) Pin definition 2  Directional output, OC gate output, open – infusion, close – withdrawal (stays open when stopped) 3  COM, ground ref. 4  Gate, TTL input, change from high to low - starts; when running stays low, change to high - stops 7  Run indicator, OC gate output, close - stopped, open – running 8  Trigger, TTL input, falling edge start/stop pump, e.g. footswitch 9  Reverse Direction, TTL input, normally low; change to high reverses. (Only applies to infuse/ withdraw mode)   LSP02(10)-1B Syringe Pump RS485 setup (Release Time：2017-01-06)  The RS485 connections are made through terminal connectors, located on the rear panel. A single PC can control up to 30 pumps. When controlled by a PC each pump must be assigned an individual address. When controlled via RS485 the pump will still respond to keypad commands. All RS485 commands settings, similar to keypad settings, are stored in EEPROM. When RS485 is enabled, RS485 interface will display communication address and band rate.   The communication address is from 1 to 30. The default address is 1. The band rate is 1200 bps, 2400 bps and 9600 bps. The default band rate is 2400 bps. RS485 format: 1 start bit, 8 data bits, 1 even parity, 1 stop. For detailed RS485 commands please see <Longer’s RS485 Protocol for LSP>. In parameters setting interface, press and turn RES to highlight the RS485 line. Set RS485 enabled. The LCD displays communication address and band rate. Turn RES to make the address highlighted. Press RES to highlight the numerical value. Turn RES to set the communication address. Press RES again to confirm and save the setting. Turn RES to highlight the band rate.  Press RES to make the numerical value highlighted. Turn RES to select the band rate. Press RES again to confirm and save the selection.   LSP02(10)-1B Syringe Pump External control function (Release Time：2017-01-06) External control function, including run/stop control input and direction control input can be enabled or disabled. 1. In parameters setting interface, press and turn RES to highlight the external control line. 2. Press RES to highlight the parameter. Turn RES to select the needed parameter. Disable: disable the external control input, that is, the input is invalid. TTL: TTL input controls the start and stop of the pump. Trigger: falling edge input controls the start and stop of the pump.   LSP02(10)-1B Syringe Pump Calibration (Release Time：2017-01-06) The flowrate can be calibrated for more accurate dispense volume. 1. In parameters setting interface, press and turn RES to highlight the Calibration line. Press RES to enter calibration interface. 2. Testing time line is highlighted. Press RES to highlight the numerical value position. Turn RES to select the testing time. The testing time is from 0.5 minutes to 60 hours. Press RES to confirm. 3. Press Run/Pause key to start the testing. After testing, turn RES to highlight the testing volume line. Press RES to highlight the numerical value position. Enter the actual volume from the membrane keypad. Press RES to confirm. 4. After calibration, the linear speed of the Pusher Block changes to increase the accuracy of the dispense volume.   LSP02(10)-1B Dual Channels Syringe Pump Pause time setting (Release Time：2017-01-06) In infusion/withdrawal mode, the pause time is set in infusion parameters setting interface. In withdrawal mode, the pause time is set in withdrawal parameters setting interface. In continuous mode, the pause time need to be set both in infusion mode interface and in withdrawal mode interface. The unit of pause time is sec, i.e. second, and the range of pause time is from 0 to 9999sec in steps of 0.1sec   LSP02(10)-1B Dual Channels Syringe Pump Flowrate setting (Release Time：2017-01-06) In parameters setting interface, turn and press RES to highlight the infusion flowrate or withdrawal flowrate setting line. Press RES to make the numerical value position highlighted. Enter the flowrate required from the membrane keypad. Press RES to set flowrate unit. Turn RES to scroll through the list and press RES to select the unit required. Possible flowrate units are µl /h, µl/m, ml/h, ml/m. The highlighted display indicates that this parameter can be changed. Note: If the number entered exceeds the maximum flowrate possible then the pump prompts the maximum feasible flowrate at the Time position. To continue enter a flowrate smaller than the maximum.   LSP02(10)-1B Dual Channels Syringe Pump Volume setting (Release Time：2017-01-06) In parameters setting interface, turn and press RES to highlight the infusion volume or withdrawal volume setting line. Press RES to make the numerical value position highlighted. Enter targeted volume from the membrane keypad. Press RES to set volume unit. Turn RES to scroll through the list and press RES to select the unit required. Possible volume units are µl and ml, i.e. microliter and milliliter. The highlighted display indicates that this parameter can be changed. Note: When the volume setting is zero, Infusion or Withdrawal modes. Volume = 0 is interpreted as no volume and the pump will run until manually stopped or a stall occurs. The LCD will display the flowrate setting. Infusion/withdrawal, Withdrawal/infusion and Continuous modes. A volume setting must be entered. If no volume is entered the motor does not run.